The most common reason that the remote start isn't working on your 2012 chevy equinox will be that the battery has gone dead on your key fob. The remote start is not working and you have to be standing on the drivers side of the car for the keyless door remote to lock/unlock the doors.
Remote start system not working on chevy equinox.
Chevy equinox remote start not working. Pin by megan elliott on things id like 2012 chevy equinox chevy equinox chevrolet equinox. We suspect it could be the sensor or the issue lighting up the sensor but were not sure. Have you checked the fob's battery?
Returned to dealer and of course no stored. I cannot even unlock the vehicle. Did all the systems/door/lock/hood latch checks.
The remote start is not working and you have to be standing on the drivers side of the car for the keyless door remote to lock/unlock the doors. Key fobs are sending a signal but my 2017 chevy equinox will not remote start or open doors any more. One or more of the vehicle doors are open, make sure they are securely closed.
If the engine on your equinox does not start when you perform the remote starting procedure, it can be due to a number of reasons: At the same time the remote starter stopped working. I've checked all the doors, hood and liftgate to make sure nothing is open.
Returned to dealer and of course no stored. The hood on your equinox is not fully closed. If your battery is defective, you probably cannot avoid replacing it.
My car alarm will also go off within 10 minutes of locking the vehicle. I have a 2013 chevy equinox with factory remote start. Remotely start or unlock your vehicle (if properly equipped) using the mychevrolet skill for alexa or my chevrolet action for google assistant vehicle management service scheduling †
The power door locks work but not the remote start. There are no messages in the dic about doors being open either. When you lock the doors the horn sounds and then you hold down the remote start button for 3 seconds or so and the lights flash but the car doesn’t start.
You can hear the car getting ready to start, you can hear the enging clicking and trying to engage to turn the engine over, but it doesn't. Car is not under warranty by a few thousand miles. Remote auto start will not start a 2007 chevy if the keyless remote works to unlock and lock the doors, then it should start the engine.
The transmission is not in park mode (p). I have a 2013 equinox lt. Remote start does not work now either.
Your battery is empty or defective. The most common reason that the remote start isn't working on your 2012 chevy equinox will be that the battery has gone dead on your key fob. Door battery check engine light gauges.
Chevy equinox remote start not working. So, i have a 2012 equinox and the autostart won't work. Changed the battery in the key fob and used the back up remote.
The main issues with the 2011 chevy equinox and it's key fob are the key fobs battery going dead, and the key fob becoming unpaired with the vehicle. On the newer gm vehicles that have the remote start function, if there is a check engine light related to the emissions system, or many other trouble code set in the computer system, it will disable the remote start feature. The remote start all of a sudden stopped working.
The remote start is not working and you have to be standing on the drivers side of the car for the keyless door remote to lock/unlock the doors. With the former, you can charge your car battery again. Regardless, the check engine light / hard to start inspection is the best way to diagnose this problem at your location.
In order to use this feature, you have to lock the doors (make sure that all door lock by pushing the lock button twice) with the remote by pushing the lock button, then you hold down the start button on the remote for 2 to 3. Press and release lock button on the rke transmitter. You push lock then start and you hear a noise and the parking lights flash just s if it started but nothing happens.
If your car does not start, there is another reason, which can usually be clearly identified by the indicator light: Immediately press and hold the remote start button for at least two seconds or until the turn signal lamps flash.