If your home was hit by a lightning strike or other power surge over the summer, it's possible the circuit breaker tripped without tipping you off, especially if your furnace is in the basement or another area you don't frequently visit. How to troubleshoot a gas fireplace.
If gas is reaching the fireplace, but it still won’t light, the next step is to light the gas jets on the gas logs, manually, following the manufacturer’s instructions.
Gas fireplace won't start after summer. There are several issues that might prevent a gas fireplace from igniting. If the pilot light isn’t on even when the fire of the fireplace is still running, you will have to take some simple measures. You should never just rush to the gas valve and start twisting it.
1) make sure the gas is on. With this short guide, turning your gas back on after a disconnect will be quick and easy. If your furnace won't turn on at all, you'll want to check the circuit breakers that service its power source.
Each time you start your gas fireplace, you’ll notice some condensation on. It also suggests that the problem is in the ignition system. Discussion starter · #1 · mar 3, 2012.
The blue flame will come on when you start the fireplace. If your fireplace isn’t starting, follow these steps. If these check out, it could be overloaded fuses or breakers, an obstruction, a gas pressure issue, moisture in the gas line, or clogged burner ports.
If gas is coming out of the pilot, but it still won't light, the spark igniter could be the problem. The thermocouple connection at the gas valve should have no thread Prepare your home by turning off all of the gas appliances.
We often have that problem in the showroom over the summer, particularly with units we don’t turn on very often; Flipped on the wall switch, took a minute or two and then fired up. Gas fireplace with the pilot always on, has a hole with key in it on the floor right next to fireplace (based on prior answers thats for gas supply), a ‘light’ switch across the room that when flipped on basically turns the flames on and entire fireplace lights up, then a knob next to the light switch that when turned clockwise increase the.
After a few minutes, the pilot is supposed to light up. Did this video solve your problem and save you money? If you’re smelling gas, then shut it off.
Try to turn the wall switch on. Or, you may don’t set the gas control knob to the pilot position. Here are some steps to take if your gas fireplace is on the fritz.
The glass on my fireplace looks smudged. So i suggest you look carefully at the condition of the pilot flame for the likely source of your problem. And the most common reason why a gas fireplace wont light when the switch is turned on is a dirty pilot burner.
Bought the house this summer, and got the pilot light lit when fall came. The gas supply to the fireplace may have been turned off during the summer months. How to turn the gas back on.
We’ll set the remote to act as a thermostat over the winter, and then in the summer, the fireplace keeps automatically turning itself off! If the pilot does not stay lit after holding the gas valve knob in for one minute, then check the thermocouple connection at the gas valve. Lighting instructions and hold the gas valve knob in for one full minute after the flame appears.
The pilot flame should look like a small, sharp blue flame, like a small blowtorch. After turning it on, wait a couple minutes, and then try lighting the fireplace again. Below are some common problems with gas fireplaces and how to fix them:
Depending on the type of gas fireplace you own, you may have a remote or receiver that run on batteries. If you run the fireplace frequently, say like every day or every few days, the fireplace starts within seconds after turning on the wall switch. Why won’t my gas fireplace start?
The first step is to make sure that your home is ready for the gas to be turned back on. You may also want to examine. Here are some potential causes:
If the gas fireplace pilot light is on but won’t start check that your gas valve is turned on and check the fuse or breakers. Joined jan 28, 2012 · 32 posts. This will make sure that there is no excess gas built up in the system.
Seems simple, but the gas valve could have gotten turned off for any number of reasons over the summer or since it was last used. However, if you don't start the fireplace for say months, like during the summer months, when you do attempt to start it again, it takes well over a minute, sometimes over two minutes. Similarly, if you don’t push the valve control knob or press the igniter repeatedly, the pilot light will never come on.
Without any gas, your fireplace won’t be able to light. Alleyne says to look for and clear out any debris between the igniter and thermocouple. Double check that the gas is actually on if your gas fireplace isn’t working correctly.
If the batteries in either of. Hold the pilot button down for a couple of minutes to purge out any trapped air. First, shut off the gas feed and wait for a few minutes.
Check the main gas valve to see if the gas is fully operational. First, take a look at the main valve to confirm that the gas is on. Make sure the gas is on.
Perhaps it is already on, but the gas hasn’t been ignited in awhile.